Model Train Forum - the complete model train resource

Model Train Forum - the complete model train resource (https://www.modeltrainforum.com/index.php)
-   O Scale (https://www.modeltrainforum.com/forumdisplay.php?f=9)
-   -   Engine id (https://www.modeltrainforum.com/showthread.php?t=187716)

ennisdavis 01-11-2020 07:02 PM

Engine id
 
2 Attachment(s)
Any info on this 1666 engine, not a lionel

T-Man 01-11-2020 07:06 PM

Yep. Missing the front truck.

ennisdavis 01-11-2020 07:41 PM

Who made it and year

Dennis461 01-11-2020 09:36 PM

Marx 2-4-2
mid 1950's

Millstonemike 01-11-2020 09:49 PM

1 Attachment(s)
Quote:

Originally Posted by ennisdavis (Post 2493216)
Who made it and year

It's a Marx postwar loco as determined by the single unit for the sliding shoes (see pic, below).

Oddly, my 1666 is a 0-4-2 with no provision for a front truck. Your 1666 shell has a pylon underneath in the rear for a trailing truck. You may have a Marx 666 motor installed given the hole in the sheet metal for a front truck.

Both motor versions are great runners. They keep chugging along, effortlessly, with a bunch of cars in tow. Just make sure it's had maintenance - motor cleaning, oiled axles, greased gears and commutator face / brush cleaning (see step-by-step, below).

Attachment 521976


You'll need some CRC cleaner (HD), GooGone or TV Tuner cleaner. 90% Isopropyl alcohol also works well. That loco will come back to life with some maintenance:

(1) Remove the motor from the shell (two screws on the side and it slides out).
(2) Remove the two screws that hold the brush plate on the motor. Clean the armature face (three sections) with CRC and Q-tips, a kitchen scrub pad (pencil eraser for stubborn spots). Clean between the three sections with a toothpick. Clean the plate's brush silos with CRC on a Q-tip. Replace the brush plate sans brushes. Then lift the tiny springs to the side of the silos, insert the brushes and replace the springs. That should get the motor running. If not, start performing the next step while turning by hand until the motor will run on its own
(3) With the motor running over newspaper, hit it with lots of CRC - inside and out, a few times or more to clean out all the old, dried up lubricants: "flush it out"
(4) There's one spot where you can use the CRC straw pinpoint nozzle to get some in the E-unit (if equipped). Repeat as necessary turning the motor over and over while do it. Note the E-unit won't cycle unless the motor is upright.
(5) Lube the axles, push-rod points and the armature's spindle. Lightly saturate the felt surrounding the spindle on the brush plate side. Use a lightweight oil (sewing machine, 3-in-1, etc.) Grease the gears. Sans grease, use a heavy motor oil (or a lightweight in a pinch).
(6) Clean the wheels for better electrical contact and grip (pulling power).
(7) Run the engine on a track. It will run better after several minutes.
(8) Have fun.

ennisdavis 01-12-2020 03:14 PM

marx
 
is this unit supppose to reverse. It does not, how do I fix that?

Millstonemike 01-12-2020 07:03 PM

Quote:

Originally Posted by ennisdavis (Post 2493470)
is this unit suppose to reverse. It does not, how do I fix that?

No reverse on the 1666, light and smoke only. But the 666 motor shown below also has the reverse unit (copper coil). You may have a 666 motor. They're all interchangable - Marx manufacturing efficiency.

You can easily remove your motor. Remove the two screws on either side of the steam chest and the motor will slide out.

If you remove it, you can see how easy it is to do basic maintenance.

ennisdavis 01-12-2020 08:00 PM

smoke
 
I dont have a smoke unit. I guess someone removed it. Are they available?

Millstonemike 01-12-2020 10:59 PM

Post a couple pic.'s of the motor.

ennisdavis 01-13-2020 07:50 PM

1 Attachment(s)
Pic of marx motor


All times are GMT -5. The time now is 08:02 AM.

Powered by vBulletin®
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.